155m SFP Optical Transceiver Bidi (PHF-8524-1LS)

Product Description

Features

l  Up to 155Mbps data links
l  Hot-pluggable SFP footprint
l  850nm Oxide VCSEL laser transmitter
l  Duplex LC connector                                       
l  RoHS Compliant and Lead-Free
l  Up to 20km on single fiber
l  Metal enclosure, for lower EMI
l  Single power supply 3.3V
l  Low power dissipation
l  Commercial operating temperature range: 0°C to 70°C
 
APPLICATIONS
 
l  155Mbps 100Base-SX Ethernet
l  SDH
 
The PHF-8524-1LS Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Std 802.3 and Fibre Channel FC- PI-2 Rev. 7.0. They are RoHS compliant and lead-free per Directive 2002/95/EC
I. Pin Descriptions

Pin	Symbol	Name/Description	Ref.
1	VEET	Transmitter Ground (Common with Receiver Ground)	1
2	TFAULT	Transmitter Fault. Not supported.
3	TDIS	Transmitter Disable. Laser output disabled on high or open.	2
4	MOD_DEF(2)	Module Definition 2. Data line for Serial ID.	3
5	MOD_DEF(1)	Module Definition 1. Clock line for Serial ID.	3
6	MOD_DEF(0)	Module Definition 0. Grounded within the module.	3
7	Rate Select	No connection required
8	LOS	Loss of Signal indication. Logic 0 indicates normal operation.	4
9	VEER	Receiver Ground (Common with Transmitter Ground)	1
10	VEER	Receiver Ground (Common with Transmitter Ground)	1
11	VEER	Receiver Ground (Common with Transmitter Ground)	1
12	RD-	Receiver Inverted DATA out. AC Coupled
13	RD+	Receiver Non-inverted DATA out. AC Coupled
14	VEER	Receiver Ground (Common with Transmitter Ground)	1
15	VCCR	Receiver Power Supply
16	VCCT	Transmitter Power Supply
17	VEET	Transmitter Ground (Common with Receiver Ground)	1
18	TD+	Transmitter Non-Inverted DATA in. AC Coupled.
19	TD-	Transmitter Inverted DATA in. AC Coupled.
20	VEET	Transmitter Ground (Common with Receiver Ground)	1

Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
 
II. Absolute Maximum Ratings
 

Parameter	Symbol	Min	Typ	Max	Unit	Ref.
Maximum Supply Voltage	Vcc	-0.5		4.0	V
Storage Temperature	TS	-40		85	°C
Case Operating Temperature	TA	0		70	°C
Relative Humidity	RH	0		85	%	1

 

Notes:
1. Non condensing.
 
 
 
 
 
 
 
III. Electrical Characteristics (TA = 0 to 70 °C, VCC = 3.0 to 3.6 Volts)
 

Parameter	Symbol	Min	Typ	Max	Unit	Ref.
Supply Voltage	Vcc	3.0		3.6	V
Supply Current	Icc		150	240	mA
Transmitter
Input differential impedance	Rin		100		Ω	2
Single ended data input swing	Vin,pp	250		1200	mV	3
Transmit Disable Voltage	VD	2		Vcc	V	4
Transmit Enable Voltage	VEN	Vee		Vee+ 0.8	V
Receiver
Single ended data output swing	Vout,pp	250	450	550	mV	5
Data output rise time	tr			175	ps	6
Data output fall time	tf			175	ps	6
Mask Margin			45%
LOS Fault	VLOS fault	2		VccHOST	V	7
LOS Normal	VLOS norm	Vee		Vee+0.5	V	7
Power Supply Rejection	PSR	100			mVpp	8
Deterministic Jitter Contribution	RX Δ DJ			51.7	ps	9
Total Jitter Contribution	RX Δ TJ		<65	122.4	ps	10

 
Notes:
2. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
3. We recommend <600mV for best EMI performance.
4. Or open circuit.
5. Into 100 ohms differential termination.
6. 20 - 80 %
7. LOS is an open collector output. Should be pulled up with 4.7k - 10k ohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.
8. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
9. Typical peak-to-peak jitter (=6*RMS width of Jitter).
10. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ.
IV. Optical Characteristics (TOP = 0 to 70 °C, VCC = 3. 00 to 3.60 Volts)

Parameter	Symbol	Min	Typ	Max	Unit	Ref
Transmitter
Output Opt. Pwr: 50 or 62.5 MMF	POUT	-9		-3	dBm	1
Optical Wavelength	λ	830		860	nm
Spectral Width	σ			0.85	nm
Optical Modulation Amplitude @ 1.0625 Gbps	OMA	156			μW	2
Optical Rise/Fall Time	tr/ tf		100	150	ps	3
Relative Intensity Noise	RIN			-120	dB/Hz
Deterministic Jitter Contribution	TX Δ DJ		20	56.5	ps	4
Total Jitter Contribution	TX Δ TJ		<65	119	ps	5
Extinction Ratio @ 1.25 Gbps	ER	9			dB
Mask Margin			45%
Receiver
Receiver Sensitivity = 1.0625 Gbps	RxSENS			-20	dBm	6
Receiver Sensitivity = 1.25 Gbps	RxSENS			-20	dBm	7
Stressed RX sens. =1.0625 Gbps		0.055			mW	8
Stressed RX sens. =1.25 Gbps				-13.5	dBm	9
Average Receiver Power	RxMAX			0	dBm
Receiver Elec. 3 dB cutoff freq.				1500	MHz
Optical Center Wavelength	λC	770		860	nm
Optical Return Loss		12			dB
LOS De-Assert	LOSD			-20	dBm
LOS Assert	LOSA	-30			dBm
LOS Hysteresis		0.5			dB

 
Notes:
1. Class 1 Laser Safety per FDA/CDRH, IEC, and EN60825-1 laser safety standards.
2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power.
3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and Δ DJ.
5. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
 
6. Specifications are for 50 micro-meter or 62.5 micro-meter fiber
7. As measured with 9dB extinction ratio.
8. Measured with conformance signals defined in FC-PI-2 Rev. 7.0 specifications.
9. Measured with conformance signals defined in IEEE 802.3 specifications.
 
V. General Specifications
 

Parameter	Symbol	Min	Typ	Max	Units	Ref.
Data Rate	BR		1.062		Gbps	1
			1.25
Bit Error Rate	BER			10^-12
Fiber Length on 50/125μm MMF	L			550 300	m	2
Fiber Length on 62.5/125μm MMF	L			300 150	m	2

 
Notes:
1. Gigabit Ethernet and 1x, Fibre Channel compatible, per IEEE 802.3 and FC-PI-2 Rev. 7.0
respectively.
2. At 1.0625 Gb/s Fibre Channel and 1.25 Gb/s Gigabit Ethernet data rates.
 
VI. Environmental Specifications
 
PHF-8524-1LS 850nm SFP transceivers have a commercial operating temperature range from 0°C to +70°C case temperature.
 

Parameter	Symbol	Min	Typ	Max	Units	Ref.
Case Operating Temperature	Top	0		70	°C
Storage Temperature	Tsto	-40		85	°C